1990-2000 Ford F-550 & F-53 Transmission Shifting Issues
Does your 1999-2000 Ford chassis motorhome start off slow from a stop and then downshifts and takes off normally? Do you notice slow takeoff from a stop and maybe a bump when taking off? Ford had an issue with these year motorhomes and put out a Technical Service Bulletin (TSB) on this issue. We have run into this several times and have the fix for it. The fix takes about 3 hours to complete and your unit will start in first gear every time after this has been done, this will save wear and tear on your transmission and make your starts much smoother and stronger.
Ever Wonder What’s in a Food Truck
The same systems that are in an RV. You have the LP system, the fresh water system and the grey water system as well as the lighting needed to work in the area. These systems are the same systems found on an RV and they mostly use the same hardware. We can work on all of those systems and we can work on the chassis also. If you have a food truck and you need repair work done on it, we can do it here locally in Denton.
Why is My RV Repair Bill so High?
We all know the frustration when a vehicle breaks down and we need to have it repaired. You take it to the repair facility and they spend an hour on it and then you get charged $150.
Alternatively, the repair shop says it needs a new part — for an additional $300, of course, it’s not in stock anywhere and needs to be ordered from the manufacturer, it may arrive in three weeks.
Why do repairs seem to cost so much even if they don’t take long? Why does it seem that the part you need is never the one that is in stock? There are several reasons for this which I will attempt to explain.
When people go to a doctor or lawyer, they’re paying for knowledge and experience; the same is true with a technician. While technicians don’t wear suits and ties, the experience and knowledge they have acquired over the years is just as valuable to someone needing a repair as a lawyer is to someone needing legal help.
To illustrate, consider the story of a large manufacturer that used an intricate machine to produce their main product. One day the machine quit running, management brought in several consultants and engineers who were unable to fix it, finally in desperation, they brought in an old engineer that had retired from the manufacturer years ago. The old engineer walked around the machine and got a hammer out of his tool bag, he knelt down and tapped the machine once at a particular spot. Immediately the machine came back to life and production started again. The old engineer sent a bill for $10,000, when asked to explain the high cost of his bill for just hitting it with a hammer the explained that $100 was for the hammer tap and $9,000 was for knowing where and how hard to tap.
Anyone who has handed his vehicle over to a mechanic knows the lesson of this legend very well. A skilled technician can strike straight to the heart of that annoyingly problem the owner was baffled by. Ultimately, the solution may come down to a matter of tightening a bolt or screw, and thus seem to have not required all that much effort. But even as he winces over the bill, the owner is struck by the realization that if the problem had been left solely up to him, he’d never have solved it or even known where to begin. Repairs may look simple, but often they’re not.
Experience and Familiarity
Modern RV’s are complex vehicles composed of multiple systems made by multiple manufacturers connected and working together as a whole unit. When one component fails in that system it’s not often apparent which component failed or even where it is located. It takes time and experience to isolate the problem down to a single component. Add to that, each RV manufacturer does things a little differently even on the same model from year to year. Each RV is a unique vehicle and as such, anything that is not a common problem can be time consuming to find and repair. We had a customer complain about the 3-hour repair cost to fix a bad wire on his generator. What he failed to consider is that his generator was not on a slide, it was bolted into the coach, it had to be completely disconnected, fuel, electrical and exhaust, and then removed from the coach with a forklift. Once out, we could then remove the covers from the generator, find and fix the wire, test to ensure that the problem was fixed and then re-install the generator in the coach. Replacing the wire was quick and simple, getting the generator out and the covers off to access the problem area was not.
Limited Working Space:
Room to work on an RV is almost nonexistent, manufacturers in their zeal to make every square inch of space usable have not considered the technician who will eventually need to repair something on it. Chassis manufacturers don’t always consider that the chassis they build will have a full-size house placed on top of it, which severely limits access to the engine and other key components of the RV. It is accessible but often it takes an acrobat or contortionist to make the repair, at the very least, the limited access takes more time than it would if the vehicle had been something other than an RV. As an example, we swapped out a diesel engine in a coach, it was approximately a 40-hour job because the engine had to come out the back of the coach and the whole back end had to be disassembled and reassembled. Plumbing and wiring are some of the most difficult systems to work on and some of the most common to have issues. Plumbing and wiring are some of the first things placed when building an RV so they are some of the most inaccessible. Ask anyone who didn’t winterize and had their plumbing freeze how costly it was to repair it. That lack of access adds up to more time to get down to the problem and repair which increases the bill.
Lack of Documentation and Technical Support:
Coach manufacturers have gotten better with their documentation but there is still much to be desired. Chassis manufacturers have done better with Freightliner and Spartan both offering 24-hour support lines and good documentation on the configuration of the unit. Workhorse is out of production since 2012 and there is no technical support offered for it anymore. Experienced mechanics can draw on their experience working on similar coaches and systems to diagnose many problems, but it is often necessary to go back to the manufacturer and get diagrams for a particular system. The manufacturers sometimes make several different configurations of the same model so getting the correct diagram is sometimes challenging and takes time. For example, we were troubleshooting an A/C problem on a Thor unit, we got 3 distinctly different A/C wiring diagrams from Thor and none of them matched the coach we had. We were able to solve the problem but only due to the experience of the technician working the problem.
Cost and Availability of Parts:
The cost of parts has risen over the years along with everything else. If you own a boat, motorcycle, jet ski or any other vehicle in the Recreational Vehicle class you already know that you pay a premium for parts for those units. There are several reasons for this:
The demand for these parts is limited, they will usually only work in one application and are not generic, this means a limited sales cycle but with the same upfront design costs of other parts. One could consider these items specialty items and that usually always means a higher cost. This means the manufacturer needs to charge more for the part to recover their costs and because they know people will pay the price to keep their unit running.
Manufacturers are getting ISO certified and must meet government regulations in the production of their products. With more and more regulations to conform to there are costs involved that will not be absorbed by the company, these are passed down to the consumer in the form of higher prices for parts and product.
Different manufacturers have different systems and responses for parts acquisition, we have good results with most of the chassis manufacturers, usually in a couple of days up to a week, Fleetwood and Rev RV can get us parts in a week usually, Winnebago can take a couple of weeks and Thor and Forest River usually takes about 4+ weeks to get us the parts we need. It helps to understand we do our best to get parts quickly, but we are often at the mercy of the manufacturer.
Since the advent of the computer age we are seeing more and more electronics in the systems on RV’s. It used to be the hot water heater, furnace, and refrigerator were a simple gas jet and a blower wheel with mechanical safeties in place to prevent a fire. Now everything is on a board with logic to turn on the blower wheel only when the flame is lit and not light the flame unless the flue is clear etc. More than not, now we replace the board rather than the igniter. Since it’s a computer board it has a higher cost than an igniter and is not as simple to replace this takes more time for the repair.
There are such a large variety of parts on any RV that nobody can be expected to carry even a majority of them. We can’t order parts based on someone’s description of them as often time it turns out to be the wrong part and then we are required to pay a 20-50% restocking fee if we can even return the part. The best we hope for is to be able to get the right part in the shortest possible time frame, we shoot for a day to a week but obviously we are limited by the vendor as to when they can get the part to us.
Cost of Business
There is a cost to do business. Most people don’t think about the utilities of running the shop, equipment, office equipment, credit card charges, the cost for the lease and the specialized insurance that is required to protect the customer and the shop from accidents and damage. Add to that the taxes the shop pays for employees, equipment, batteries sold and other things that the state and local governments can tax to get their revenue that adds to the total cost of repair.
RV’s offer a lot of fun and adventure, but they are expensive to purchase and maintain. My hope is that after reading this you will have a better understanding of the factors to consider that go into the repair cost of your RV.
The Art of Troubleshooting
Vehicles are composed of complex systems that many times depend on one another to function properly. When something goes wrong it is not always obvious as to what is the problem is. In a system of many connected components, which one has failed and is causing the problem? Nobody can look at a problem and tell what the source of the problem is with absolute certainty unless they are a magician. One way to identify the problem is through effective troubleshooting. Let’s start with a definition of troubleshooting:
Troubleshooting is a systematic approach to solving a problem and is commonly used to find and correct issues with complex systems such as electronics, hydraulics, pneumatics, computers, networks, etc. The largest consideration to understand is that it takes time to effectively troubleshoot an issue.
The first step in troubleshooting is to gather the necessary information on the issue, information such as the undesired behavior or the lack of expected functionality. This is usually supplied by the customer when dropping off their vehicle. Additional, important information will include related symptoms and any special circumstances that may be required to reproduce the issue.
Once the issue and how to reproduce it are understood, the next step is usually to verify and eliminate individual components in the system and verify that the issue persists, this also serves to rule out incompatibility and third-party causes.
Assuming the issue remains after step 2, the troubleshooter will most likely check common causes. Depending on the particular issue and the troubleshooter’s experience, he/she may have some ideas about components that usually fail. They may also check product documentation and/or conduct research with the vendor or on the web. Some manufacturers provide extensive or even good troubleshooting information, Workhorse is one of these; however, most manufacturer do not provide much if any troubleshooting information, sadly, this is especially true in the RV field.
After all the common causes of the problem are ruled out, the troubleshooter may resort to a more systematic and logical process of verifying the expected function of the individual parts in the system. One effective method is the split-half approach. With a problem resulting from several possible components in series, the troubleshooter tests half-way down the line of components. If the middle component works, he/she splits to the middle of the start and the middle component just verified. If the test finds a problem at the mid-point, he/she does a split towards the start of the line until the problem component is found. The split-half process can save time in complex systems that depend on many components.
Once the problem part is identified, it may be repaired or replaced as needed. Evidence of effective troubleshooting is obvious when the issue is no longer present, and proper operation is restored.
The success of troubleshooting often depends on the thoroughness and experience of the person troubleshooting the issue and the information available to him/her. Troubleshooting is as much an art as it is a skill.
New Name & Website
We are changing the name Danny’s RV to Kampfam RV & Truck Service, we feel this name change better represents the industry that we work in and goes with our expanded service offerings. We retain the same location, services, and excellant quality of work as before so there are no changes that way. This will be an intentionally slow process as the Danny’s RV name is very well know. We are starting this transition with a new updated website designed to introduce the Kampfam RV & Truck Service name alongside the Danny’s RV name to our longstanding customers and provide more and better content to our customers. Check back often as I build out the site and provide more information, let me know if there is information you would like to see here.
It’s Spring 2018
It’s spring 2018 and the rain is upon us, we have had a pretty wet spring so far. Water entry into your RV is one of the greatest sources of structural issues for an RV. Let us check the integrity of your RV roof and ensure there is no place for water entry into your vehicle. Water entry from a roof leak will quickly turn into a major repair nightmare.
We Work on Medium & Heavy Trucks Also
There are two components to an RV, the chassis and the house, there really isn’t any difference between a truck and an RV when it comes to the chassis. Our owner has 20 years experience with over the road trucks and as a result, Kampfam is expanding it’s service offerings to include medium and heavy trucks, if you have or know of someone who has a medium or heavy truck, we can provide the same quality services to them that we currently provide to our RV customers.
Kampfam Purchased Danny’s RV Service
In August 2017, Kevin and Marsha Pestrue purchased Danny’s RV Service from Charles Cram. Charles retired from the business and we hope he enjoys his retirement. We are excited to be working in this ever changing industry. Kevin has 20 years of experience in the diesel field working on over the road trucks and heavy equipment, and 20 years in the IT field working with network and server companies. Marsha works as a Dental Hygienist in Coppell, has 20 years in the marketing field and loves meeting new people.